summaryrefslogtreecommitdiff
path: root/cleopatre/devkit/rt5572drv/MODULE/include/rt_led.h
diff options
context:
space:
mode:
Diffstat (limited to 'cleopatre/devkit/rt5572drv/MODULE/include/rt_led.h')
-rw-r--r--cleopatre/devkit/rt5572drv/MODULE/include/rt_led.h200
1 files changed, 200 insertions, 0 deletions
diff --git a/cleopatre/devkit/rt5572drv/MODULE/include/rt_led.h b/cleopatre/devkit/rt5572drv/MODULE/include/rt_led.h
new file mode 100644
index 0000000000..204b19e4ff
--- /dev/null
+++ b/cleopatre/devkit/rt5572drv/MODULE/include/rt_led.h
@@ -0,0 +1,200 @@
+/****************************************************************************
+ * Ralink Tech Inc.
+ * 4F, No. 2 Technology 5th Rd.
+ * Science-based Industrial Park
+ * Hsin-chu, Taiwan, R.O.C.
+ * (c) Copyright 2002-2010, Ralink Technology, Inc.
+ *
+ * All rights reserved. Ralink's source code is an unpublished work and the
+ * use of a copyright notice does not imply otherwise. This source code
+ * contains confidential trade secret material of Ralink Tech. Any attemp
+ * or participation in deciphering, decoding, reverse engineering or in any
+ * way altering the source code is stricitly prohibited, unless the prior
+ * written consent of Ralink Technology, Inc. is obtained.
+ ****************************************************************************
+
+ Module Name:
+ rt_led.h
+
+ Abstract:
+
+ Revision History:
+ Who When What
+ --------- ---------- ----------------------------------------------
+ */
+
+#ifndef __RT_LED_H__
+#define __RT_LED_H__
+
+/* LED MCU command */
+#define MCU_SET_LED_MODE 0x50
+#define MCU_SET_LED_GPIO_SIGNAL_CFG 0x51
+#define MCU_SET_LED_AG_CFG 0x52
+#define MCU_SET_LED_ACT_CFG 0x53
+#define MCU_SET_LED_POLARITY 0x54
+#ifdef WSC_INCLUDED
+#ifdef WSC_LED_SUPPORT
+#define MCU_SET_WPS_LED_MODE 0x55 /* Set WPS LED mode (based on WPS specification V1.0). */
+#define MCU_SET_ANT_DIVERSITY 0x73
+#endif /* WSC_LED_SUPPORT */
+#endif /* WSC_INCLUDED */
+
+/* LED Mode */
+#define LED_MODE(pAd) ((pAd)->LedCntl.MCULedCntl.field.LedMode & 0x7F)
+#define LED_HW_CONTROL 19 /* set LED to controll by MAC registers instead of by firmware */
+#define LED_MODE_DEFAULT 0 /* value domain of pAd->LedCntl.LedMode and E2PROM */
+#define LED_MODE_TWO_LED 1
+#define LED_MODE_8SEC_SCAN 2 /* Same as LED mode 1; except that fast blink for 8sec when doing scanning. */
+#define LED_MODE_SITE_SURVEY_SLOW_BLINK 3 /* Same as LED mode 1; except that make ACT slow blinking during site survey period and blink once at power-up. */
+#define LED_MODE_WPS_LOW_POLARITY 4 /* Same as LED mode 1; except that make ACT steady on during WPS period */
+#define LED_MODE_WPS_HIGH_POLARITY 5 /* Same as LED mode 1; except that make ACT steady on during WPS period */
+/*#define LED_MODE_SIGNAL_STREGTH 8 // EEPROM define =8 */
+#define LED_MODE_SIGNAL_STREGTH 0x40 /* EEPROM define = 64 */
+#ifdef WSC_INCLUDED
+#ifdef WSC_LED_SUPPORT
+#define LED_WPS_MODE10_TURN_ON 16 /* For Dlink WPS LED, turn the WPS LED on */
+#define LED_WPS_MODE10_FLASH 17 /* For Dlink WPS LED, let the WPS LED flash */
+#define LED_WPS_MODE10_TURN_OFF 18 /* For Dlink WPS LED, turn the WPS LED off */
+#define WPS_LED_MODE_7 0x07
+#define WPS_LED_MODE_8 0x08
+#define WPS_LED_MODE_9 0x09
+#define WPS_LED_MODE_10 0x0a
+/* */
+/* Chungwa Telecom (WPS LED and SD/HD LEDs) use WPS LED mode #11 and it is based on mode #7 */
+/* */
+/* GPIO #1: WPS LED */
+/* GPIO #2: SD (Standard Definition) LED */
+/* GPIO #4: HD (High Definition) LED */
+/* */
+#define WPS_LED_MODE_11 0x0b
+#define WPS_LED_MODE_12 0x0c
+#endif /* WSC_LED_SUPPORT */
+#endif /* WSC_INCLUDED */
+
+/* Driver LED Status */
+#define LED_LINK_DOWN 0
+#define LED_LINK_UP 1
+#define LED_RADIO_OFF 2
+#define LED_RADIO_ON 3
+#define LED_HALT 4
+#define LED_WPS 5
+#define LED_ON_SITE_SURVEY 6
+#define LED_POWER_UP 7
+#ifdef WSC_INCLUDED
+#ifdef WSC_LED_SUPPORT
+/* For LED mode = 7 only */
+#define LED_WPS_IN_PROCESS 8 /* The protocol is searching for a partner, connecting, or exchanging network parameters. */
+#define LED_WPS_ERROR 9 /* Some error occurred which was not related to security, such as failed to find any partner or protocol prematurely aborted. */
+#define LED_WPS_SESSION_OVERLAP_DETECTED 10 /* The Protocol detected overlapping operation (more than one Registrar in PBC mode): could be a security risk. */
+#define LED_WPS_SUCCESS 11 /* The protocol is finished: no uncorrectable errors occured. Normally after guard time period. */
+#define LED_WPS_TURN_LED_OFF 12 /* Turn the WPS LEDs off. */
+#define LED_WPS_TURN_ON_BLUE_LED 13 /* Turn on the WPS blue LED. */
+#define LED_NORMAL_CONNECTION_WITHOUT_SECURITY 14 /* Successful connection with an AP using OPEN-NONE. */
+#define LED_NORMAL_CONNECTION_WITH_SECURITY 15 /* Successful connection with an AP using an encryption algorithm. */
+/* For LED Share Mode */
+#endif /* WSC_LED_SUPPORT */
+#endif /* WSC_INCLUDED */
+
+/* MCU Led Link Status */
+#define LINK_STATUS_LINK_DOWN 0x20
+#define LINK_STATUS_ABAND_LINK_UP 0xa0
+#define LINK_STATUS_GBAND_LINK_UP 0x60
+#define LINK_STATUS_RADIO_ON 0x20
+#define LINK_STATUS_RADIO_OFF 0x00
+#define LINK_STATUS_WPS 0x10
+#define LINK_STATUS_ON_SITE_SURVEY 0x08
+#define LINK_STATUS_POWER_UP 0x04
+#define LINK_STATUS_HW_CONTROL 0x00
+#ifdef WSC_INCLUDED
+#ifdef WSC_LED_SUPPORT
+/* LED mode = 7 and 8 only */
+#define LINK_STATUS_WPS_IN_PROCESS 0x00 /* The protocol is searching for a partner, connecting, or exchanging network parameters. */
+#define LINK_STATUS_WPS_SUCCESS_WITH_SECURITY 0x01 /* The protocol is finished (with security): no uncorrectable errors occured. Normally after guard time period. */
+#define LINK_STATUS_WPS_ERROR 0x02 /* Some error occurred which was not related to security, such as failed to find any partner or protocol prematurely aborted. */
+#define LINK_STATUS_WPS_SESSION_OVERLAP_DETECTED 0x03 /* The Protocol detected overlapping operation (more than one Registrar in PBC mode): could be a security risk. */
+#define LINK_STATUS_WPS_TURN_LED_OFF 0x04 /* Turn the WPS LEDs off. */
+#define LINK_STATUS_WPS_SUCCESS_WITHOUT_SECURITY 0X05 /* The protocol is finished (without security): no uncorrectable errors occured. Normally after guard time period. */
+#define LINK_STATUS_NORMAL_CONNECTION_WITHOUT_SECURITY 0x06 /* Successful connection with an AP using OPEN-NONE. */
+#define LINK_STATUS_NORMAL_CONNECTION_WITH_SECURITY 0x0E /* Successful connection with an AP using an encryption algorithm. */
+#define LINK_STATUS_WPS_BLUE_LED 0x01 /* WPS blue LED. */
+/* LED moe = 10 */
+#define LINK_STATUS_WPS_MODE10_TURN_ON 0x00 /*Use only on Dlink WPS LED (mode 10), turn the WPS LED on. */
+#define LINK_STATUS_WPS_MODE10_FLASH 0x01 /*Use only on Dlink WPS LED (mode 10), let the WPS LED flash, three times persecond. */
+#define LINK_STATUS_WPS_MODE10_TURN_OFF 0x02 /*Use only on Dlink WPS LED (mode 10), turn the WPS LED off. */
+#endif /* WSC_LED_SUPPORT */
+#endif /* WSC_INCLUDED */
+
+
+#define ACTIVE_LOW 0
+#define ACTIVE_HIGH 1
+
+/* */
+/* MCU_LEDCS: MCU LED Control Setting. */
+/* */
+typedef union _MCU_LEDCS_STRUC {
+ struct {
+#ifdef RT_BIG_ENDIAN
+ UCHAR Polarity:1;
+ UCHAR LedMode:7;
+#else
+ UCHAR LedMode:7;
+ UCHAR Polarity:1;
+#endif /* RT_BIG_ENDIAN */
+ } field;
+ UCHAR word;
+} MCU_LEDCS_STRUC, *PMCU_LEDCS_STRUC;
+
+void RTMPGetLEDSetting(IN RTMP_ADAPTER *pAd);
+void RTMPInitLEDMode(IN RTMP_ADAPTER *pAd);
+void RTMPExitLEDMode(IN RTMP_ADAPTER *pAd);
+
+VOID RTMPSetLEDStatus(
+ IN PRTMP_ADAPTER pAd,
+ IN UCHAR Status);
+
+#ifdef RTMP_MAC_USB
+#define RTMPSetLED(pAd, Status) \
+do{ \
+ UCHAR LEDStatus; \
+ LEDStatus = Status; \
+ if (Status == LED_RADIO_OFF)\
+ RTMPSetLEDStatus(pAd, Status);\
+ else\
+ RTEnqueueInternalCmd(pAd, CMDTHREAD_SET_LED_STATUS, &LEDStatus, sizeof(LEDStatus)); \
+}while(0)
+
+#endif /* RTMP_MAC_USB */
+
+
+VOID RTMPSetSignalLED(
+ IN PRTMP_ADAPTER pAd,
+ IN NDIS_802_11_RSSI Dbm);
+
+#ifdef WSC_STA_SUPPORT
+#ifdef WSC_LED_SUPPORT
+VOID LEDConnectionStart(
+ IN PRTMP_ADAPTER pAd);
+
+VOID LEDConnectionCompletion(
+ IN PRTMP_ADAPTER pAd,
+ IN BOOLEAN bSuccess);
+#endif /* WSC_LED_SUPPORT */
+#endif /* WSC_STA_SUPPORT */
+
+
+typedef struct _LED_CONTROL
+{
+ MCU_LEDCS_STRUC MCULedCntl; /* LED Mode EEPROM 0x3b */
+ USHORT LedAGCfg; /* LED A/G Configuration EEPROM 0x3c */
+ USHORT LedACTCfg; /* LED ACT Configuration EEPROM 0x3e */
+ USHORT LedPolarity;/* LED A/G/ACT polarity EEPROM 0x40 */
+ UCHAR LedIndicatorStrength;
+ UCHAR RssiSingalstrengthOffet;
+ BOOLEAN bLedOnScanning;
+ UCHAR LedStatus;
+}LED_CONTROL, *PLED_CONTROL;
+
+void RTMPStartLEDMode(IN RTMP_ADAPTER *pAd);
+
+#endif /* __RT_LED_H__ */
+