From 79603022422cec39ea44686c84a1050acd0c145e Mon Sep 17 00:00:00 2001 From: Michael Terhar Date: Sat, 26 Aug 2017 23:33:33 -0400 Subject: Keymaps for several of my boards (#1641) * copied mjt keymaps from archive * All mjt boards now compile * fixed jd45-mjt breathing * Updates to fix SpaceFN but not tested yet. * Still missing either spacebar or an adjacent keypress. * Debugging rigged up for use with hid_listen. * Reverted the default keymap to use tap_layer_key rather than custom. Moved custom approach to keymap_debug.c * Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function. * Cleaned up JD45 keymap that uses tapkey. * Redid minivan keymap with numsym rather than raise/lower. Untested. * Created my MJT keymap for HHKB Enabled dynamic macros and moved somoe of the shortcuts around. * Minor keymap fixes to make them compile without errors. * Added home/end to right arrow cluster on DYN layer. * Added more keys to fn and dyn layers. * It wasn't using my custom layer last time somehow...? Now it will. * Compiled and installed at end of day on 8/23 * Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback. * Fixed volume controls... were reversed and disabled. * Added F13-F15 back to fkeys layer in Minivan * Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan. * Removed DYN layer. * Fixed diagram in planck numsym. * Cleanup for pull request. * Roadkit flip phone warning. * Replaced PLAY_NOTES_ARRAY to PLAY_SONG * reset the submodules * checked out specific commits for submodules * Removed debugging from JD45 shared config.h * Moved custom rules.mk to apropriate keymap Reset the shared rules.mk file. * Trailing return issue in rules.mk Gotta make for a smooth pull request :-) --- keyboards/jd45/keymaps/mjt/rules.mk | 67 +++++++++++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) create mode 100644 keyboards/jd45/keymaps/mjt/rules.mk (limited to 'keyboards/jd45/keymaps/mjt/rules.mk') diff --git a/keyboards/jd45/keymaps/mjt/rules.mk b/keyboards/jd45/keymaps/mjt/rules.mk new file mode 100644 index 000000000..6eec21160 --- /dev/null +++ b/keyboards/jd45/keymaps/mjt/rules.mk @@ -0,0 +1,67 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +# UNICODE_ENABLE = YES # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -- cgit v1.2.3