summaryrefslogtreecommitdiff
path: root/keyboard/infinity/tool/k20dx32_flash.cfg
diff options
context:
space:
mode:
Diffstat (limited to 'keyboard/infinity/tool/k20dx32_flash.cfg')
-rw-r--r--keyboard/infinity/tool/k20dx32_flash.cfg139
1 files changed, 0 insertions, 139 deletions
diff --git a/keyboard/infinity/tool/k20dx32_flash.cfg b/keyboard/infinity/tool/k20dx32_flash.cfg
deleted file mode 100644
index 1e3deb091..000000000
--- a/keyboard/infinity/tool/k20dx32_flash.cfg
+++ /dev/null
@@ -1,139 +0,0 @@
-# FreeScale Kinetis K20 devices with 32kB Flash and 8kB Local On-Chip SRAM,
-# Nemuisan's Special for MK20DN32VFT5,MK20DX32VFT5,MK10DN32VFT5,MK10DX32VFT5
-
-
-# 0.8.0 has no these procs
-proc using_jtag {} {
- set _TRANSPORT [ transport select ]
- expr { [ string first "jtag" $_TRANSPORT ] != -1 }
-}
-
-proc using_swd {} {
- set _TRANSPORT [ transport select ]
- expr { [ string first "swd" $_TRANSPORT ] != -1 }
-}
-
-proc using_hla {} {
- set _TRANSPORT [ transport select ]
- expr { [ string first "hla" $_TRANSPORT ] != -1 }
-}
-
-source [find target/swj-dp.tcl]
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME k20
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
-} else {
- if { [using_jtag] } {
- set _CPUTAPID 0x4BA00477
- } {
- # this is the SW-DP tap id not the jtag tap id
- set _CPUTAPID 0x2BA01477
- }
-}
-
-# Work-area is a space in RAM used for flash programming
-# By default use 8kB
-if { [info exists WORKAREASIZE] == 0 } {
- set _WORKAREASIZE 0x2000
-}
-
-# Select "srst_only", Nemuisan said so!
-echo "Kinetis MUST need Hardware SRST Control to Recover Secure-State!"
-adapter_nsrst_delay 200
-reset_config srst_only
-
-swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -chain-position $_TARGETNAME
-
-# It is important that "kinetis mdm check_security" is called for
-# 'examine-end' event and not 'eximine-start'. Calling it in 'examine-start'
-# causes "kinetis mdm check_security" to fail the first time openocd
-# calls it when it tries to connect after the CPU has been power-cycled.
-$_CHIPNAME.cpu configure -event examine-end {
- kinetis mdm check_security
-# Uncomment when gone into s*ck'n secured state!
-# kinetis mdm mass_erase
-}
-
-# K20 has minimun 8kB of SRAM and starts at 1FFFF000.
-$_TARGETNAME configure -work-area-phys 0x1FFFF000 -work-area-size $_WORKAREASIZE -work-area-backup 0 -rtos auto
-
-# MK20DN32VFT5,MK20DX32VFT5,MK10DN32VFT5,MK10DX32VFT5 has 32kB of flash memory.
-flash bank $_CHIPNAME.pflash kinetis 0x00000000 0x8000 0 4 $_TARGETNAME
-
-
-proc mt_flash {IMGFILE} {
- flash write_image erase $IMGFILE
- reset run
- halt
- verify_image $IMGFILE
- reset run
- shutdown
-}
-
-proc mt_flash_bin {IMGFILE OFFSET} {
- flash write_image erase $IMGFILE $OFFSET bin
- reset run
- halt
- verify_image $IMGFILE $OFFSET bin
- reset run
- shutdown
-}
-
-proc mt_flash_hex {IMGFILE} {
- flash write_image erase $IMGFILE 0 ihex
- reset run
- halt
- verify_image $IMGFILE 0 ihex
- reset run
- shutdown
-}
-
-proc mt_flash_srec {IMGFILE} {
- flash write_image erase $IMGFILE 0 s19
- reset run
- halt
- verify_image $IMGFILE 0 s19
- reset run
- shutdown
-}
-
-proc mass_erase {} {
- kinetis mdm mass_erase
-}
-
-proc eraser {} {
-# Verbose procedure confirmed erase routine
- flash info 0
-# CAUTION! "flash erase_sector 0 0 last" goes into secure state!!!
-# USE "mass_erase" command instead of
-# flash erase_sector 0 0 last
- mass_erase
- shutdown
-}
-
-#debug_level 3
-# HLA doesn't have cortex_m commands
-if {![using_hla]} {
- # if srst is not fitted use SYSRESETREQ to
- # perform a soft reset
- cortex_m reset_config sysresetreq
-}
-adapter_khz 1000
-reset_config srst_only srst_nogate connect_assert_srst
-gdb_target_description disable
-init
-reset init