ubuntu@ubuntu:~/LUFA/Bootloaders/LUFA_DFU_Bootloader_AT90USB162$ sudo avrdude -vv -F -P /dev/ttyACM0 -c avr910 -p usb162 -U flash:w:BootloaderDFU.hex avrdude: Version 5.5, compiled on May 9 2008 at 13:04:46 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ System wide configuration file is "/etc/avrdude.conf" User configuration file is "/home/ubuntu/.avrduderc" User configuration file does not exist or is not a regular file, skipping Using Port : /dev/ttyACM0 Using Programmer : avr910 AVR Part : AT90USB162 Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 10 8 0 no 512 4 0 9000 9000 0x00 0x00 flash 65 6 128 0 yes 16384 128 128 4500 4500 0x00 0x00 lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : avr910 Description : Atmel Low Cost Serial Programmer Found programmer: Id = "AVR ISP"; type = S Software Version = 2.3; Hardware Version = 1.0 Programmer supports auto addr increment. Programmer supports the following devices: Device code: 0x55 = ATtiny12 Device code: 0x56 = ATtiny15 Device code: 0x5e = ATtiny2313 Device code: 0x76 = ATMEGA8 Device code: 0x74 = ATMEGA6450 Device code: 0x72 = ATMEGA32 Device code: 0x45 = ATMEGA64 Device code: 0x74 = ATMEGA6450 Device code: 0x43 = ATMEGA128 Device code: 0x63 = ATMEGA162 Device code: 0x78 = ATMEGA169 Device code: 0x6c = AT90S4434 Device code: 0x38 = AT90S8515 Device code: 0x65 = (unknown) avrdude: warning: selected device is not supported by programmer: usb162 avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e9482 avrdude: safemode: lfuse reads as 5E avrdude: safemode: hfuse reads as D9 avrdude: safemode: efuse reads as F4 avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "BootloaderDFU.hex" avrdude: input file BootloaderDFU.hex auto detected as Intel Hex avrdude: writing flash (16066 bytes): Writing | ################################################## | 100% 33.39s avrdude: 16066 bytes of flash written avrdude: verifying flash memory against BootloaderDFU.hex: avrdude: load data flash data from input file BootloaderDFU.hex: avrdude: input file BootloaderDFU.hex auto detected as Intel Hex avrdude: input file BootloaderDFU.hex contains 16066 bytes avrdude: reading on-chip flash data: Reading | ################################################## | 100% 16.07s avrdude: verifying ... avrdude: 16066 bytes of flash verified avrdude: safemode: lfuse reads as 5E avrdude: safemode: hfuse reads as D9 avrdude: safemode: efuse reads as F4 avrdude: safemode: Fuses OK avrdude done. Thank you.