/** \file * * This file contains special DoxyGen information for the generation of the main page and other special * documentation pages. It is not a project source file. */ /** \page Page_ChangeLog Project Changelog * * \section Sec_ChangeLog090209 Version 090209 * * - PWM timer mode in AudioOut demo changed to Fast PWM for speed * - Updated Magstripe project to work with the latest hardware revision * - Fixed library not responding to the BCERRI flag correctly in host mode, leading to device lockups * - Fixed library handling Get Descriptor requests when not addressed as standard requests to the device or interface * - Fixed serious data corruption issue in MassStorage demo dataflash write routine * - Added new NO_CLEARSET_FEATURE_REQUEST compile time token * - USB task now restores previous global interrupt state after execution, rather than forcing global interrupts to be enabled * - Fixed USB_DeviceEnumerationComplete event firing after each configuration change, rather than once after the initial configuration * - Added ENDPOINT_DOUBLEBANK_SUPPORTED() macros to Endpoint.h, altered ENDPOINT_MAX_SIZE() to allow user to specify endpoint * - ENDPOINT_MAX_ENDPOINTS changed to ENDPOINT_TOTAL_ENDPOINTS, PIPE_MAX_PIPES changed to PIPE_TOTAL_PIPES * - Endpoint and Pipe non-control stream functions now ensure endpoint or pipe is ready before reading or writing * - Changed Teensy bootloader to use a watchdog reset when exiting rather than a software jump * - Fixed integer promotion error in MassStorage and MassStorageHost demos, corrupting read/write transfers * - SPI_SendByte is now SPI_TransferByte, added new SPI_SendByte and SPI_ReceiveByte functions for fast one-way transfer * - MassStorage demo changed to use new fast one-way SPI transfers to increase throughput * - MassStorage handling of Mass Storage Reset class request improved * - Altered MassStorage demo dataflash block read code for speed * - Added USB_IsSuspended global flag * - Simplified internal Dual Mode (OTG) USB library code to reduce code size * - Extended stream timeout period to 100ms from 50ms * - Mass Storage Host demo commands now all return an error code from the Pipe_Stream_RW_ErrorCodes_t enum * - Added SubErrorCode parameter to the USB_DeviceEnumerationFailed event * - VBUS drop interrupt now disabled during the manual-to-auto VBUS delivery handoff * - Simplified low level backend so that device/host mode initialization uses the same code paths * - Added workaround for faulty Mass Storage devices which do not implement the required GET_MAX_LUN request * - Removed buggy Telnet application from the RNDIS demo * - Moved Mass Storage class requests in the Mass Storage Host demo to wrapper functions in MassStoreCommands.c * - Fixed incorrect SCSI command size value in the Request Sense command in MassStoreCommands.c * - Added SetProtocol request to HID class non-parser Mouse and Keyboard demos to force devices to use the correct Boot Protocol * - Added new "dfu" and "flip" programming targets to project makefiles * - HID_PARSE_Sucessful enum member typo corrected to HID_PARSE_Successful * - Changed COLLECTION item strucutres in the HID descriptor parser to include the collection's Usage Page value * - Serial driver now sets Tx line as output, enables pullup on Rx line * - Fixed smaller USB AVRs raising multiple connection and disconnection events when NO_LIMITED_CONTROLLER_CONNECT is disabled * - Added HOST_DEVICE_SETTLE_DELAY_MS to give the host delay after a device is connected before it is enumerated * - Fixed KeyboardHostWithParser demo linking against the wrong global variables * - Completed doxygen documentation of remaining library bootloaders, demos and projects * - Fixed incorrect bootloader start address in the TeensyHID bootloader * - Added HWB button whole-disk ASCII dump functionality to MassStoreHost demo * - Replaced printf_P(PSTR("%c"), {Variable}) calls with putchar() for speed and size savings * - Serial driver now accepts baud rates over 16-bits in size, added double speed flag option * - Fixed incorrect callback abort return value in Pipe.c * - Added new flip-ee and dfu-ee makefile targets (courtesy of Opendous Inc.) * - Removed reboot-on-disconnect code from the TeensyHID bootloader, caused problems on some systems * - Fixed AudioOutput and AudioInput demos looping on the endpoint data, rather than processing a sample at a time and returning * each time the task runs to allow for other tasks to execute * - Added support for the Atmel ATAVRUSBRF01 board * - Added AVRISP Programmer Project, courtesy of Opendous Inc. * - Fixed CDC Host demo not searching through both CDC interfaces for endpoints * - Fixed incorrect Product String descriptor length in the DFU class bootloader * - Fixed failed descriptor searches in ConfigDescriptor.c eating the last checked descriptor when another search is started * * \section Sec_ChangeLog081224 Version 081224 * * - MyUSB name changed to LUFA, the Lightweight USB Framework for AVRs * - Fixed Mass Storage Host demo's MassStore_SendCommand() delay in the incorrect place * - Fixed USBtoSerial demo not calling ReconfigureUSART() after a change in the line encoding * - Fixed infinite loop in host mode Host-to-Device control transfers with data stages * - HID report parser now supports devices with multiple reports in one interface via Report IDs * - Fixed RZUSBSTICK board LED driver header incorrect macro definition order causing compile errors * - Calling USB_Init() when the USB interface is already configured now forces a complete interface reset * and re-enumeration - fixes MyUSB DFU bootloader not switching to app code correctly when soft reset used * - Fixed "No newline at end of file" warning when stream callbacks are enabled * - DFU bootloader now uses fixed signature bytes per device, rather than reading them out dynamically for size * - Added new FIXED_CONTROL_ENDPOINT_SIZE and USE_SINGLE_DEVICE_CONFIGURATION switches to statically define certain values to * reduce compiled binary size * - Added new NO_LIMITED_CONTROLLER_CONNECT switch to prevent the library from trying to determine bus connection * state from the suspension and wake up events on the smaller USB AVRs * - Added summary of all library compile time tokens to the documentation * - Added overview of the LUFA scheduler to the documentation * - Removed MANUAL_PLL_CONTROL compile time token, replaced with a mask for the USB_Init() Options parameter * - CDC bootloader now uses the correct non-far or far versions of the pgm_* functions depending on if RAMPZ is defined * - Doxygen documentation now contains documentation on all the projects, bootloaders and most demos included with the library * - CDC bootloader now runs user application when USB disconnected rather than waiting for a hard reset * - MouseHostWithParser and KeyboardHostWithParser now support multiple-report devices * - RNDIS demo can now close connections correctly using the new TCP_APP_CLOSECONNECTION() macro - used in Webserver * - Fixed the DFU bootloader, no longer freezes up when certain files are programmed into an AVR, made reading/writing faster * - Fixed mouse/joystick up/down movements reversed - HID mouse X/Y coordinates use a left-handed coordinate system, not a normal * right-handed system * - Added stub code to the CDC and USBtoSerial demos showing how to read and set the RS-232 handshake lines - not currently used in * the demos, but the example code and supporting defines are now in place * - Interrupts are now disabled when processing a control request in device mode, to avoid exceeding the strict control request * timing requirements. * - All demos now use a central StatusUpdate() function rather than direct calls to the board LED functions, so that the demos can * easily be altered to show different LED combinations (or do something else entirely) as the demo's status changes * - Removed LED commands from the CDC bootloader, unused by most AVR910 programming software * - Fixed RNDIS demo ICMP ping requests echoing back incorrect data * - Added DHCP server code to RNDIS demo, allowing for hands-free autoconfiguration on any PC * - Fixed DFU bootloader PID value for the ATMEGA16U4 AVR * - Endpoint and Pipe configuration functions now return an error code indicating success or failure * - USB Reset in device mode now resets and disables all device endpoints * - Added intermediate states to the host mode state machine, reducing the USB task blocking time to no more than 1ms explicitly per * invocation when in host mode * - Added support for the ATMEGA32U6 microcontroller * - Added STATIC_ENDPOINT_CONFIGURATION compile time option, enabled in the bootloaders to minimize space usage * - Removed redudant code from the USB device GetStatus() chapter 9 processing routine * - Added new TeensyHID bootloader, compatible with the Teensy HID protocol (http://www.pjrc.com/teensy/) * - Versions are now numbered by release dates, rather than arbitrary major/minor revision numbers * - USB_RemoteWakeupEnabled is now correctly set and cleared by SetFeature and ClearFeature requests from the host * - Changed prototype of GetDescriptor, so that it now returns the descriptor size (or zero if the descriptor doesn't exist) * rather than passing the size back to the caller through a parameter and returning a boolean * * \section Sec_ChangeLog153 Version 1.5.3 - Released 2nd October, 2008 * * - Fixed CDC bootloader using pgmspace macros for some descriptors inappropriately * - Updated all Mouse and Keyboard device demos to include boot protocol support (now works in BIOS) * - Renamed bootloader directories to remove spaces, which were causing build problems on several OSes * - Removed serial number strings from all but the MassStore demo where it is required - users were not * modifing the code to either ommit the descriptor or use a unique serial per device causing problems * when multiple units of the same device were plugged in at the same time * - AudioOutput and AudioInput demos now correctly silence endpoints when not enabled by the host * - Added KeyboardMouse demo (Keyboard and Mouse functionality combined into a single demo) * - Added DriverStubs directory to house board level driver templates, to make MyUSB compatible custom board * driver creation easier * - Extended MassStorage demo to support multiple LUNs, 2 by default * - Fixed incorrect device address mask, preventing the device from enumerating with addresses larger than 63 * - Fixed incorrect data direction mask in the GetStatus standard request, preventing it from being handled * - Fixed incorrect GetStatus standard request for endpoints, now returns the endpoint STALL status correctly * - Added in new USB_RemoteWakeupEnabled and USB_CurrentlySelfPowered flags rather than using fixed values * - Added DualCDC demo to demonstrate the use of Interface Association Descriptors * - Added pipe NAK detection and clearing API * - Added pipe status change (NAK, STALL, etc.) interrupt API * - Fixed MassStorageHost demo so that it no longer freezes randomly when issuing several commands in a row * - Host demos configuration descriptor routines now return a unique error code when the returned data does * not have a valid configuration descriptor header * - Added Endpoint_WaitUntilReady() and Pipe_WaitUntilReady() functions * - Stream functions now have software timeouts, timeout period can be set by the USB_STREAM_TIMEOUT_MS token * - All demos now pass the USB.org automated Chapter 9 device compliance tests * - All HID demos now pass the USB.org automated HID compliance tests * - Polling interval of the interrupt endpoint in the CDC based demos changed to 0xFF to fix problems on Linux systems * - Changed stream functions to accept a new callback function, with NO_STREAM_CALLBACKS used to disable all callbacks * - Mass Storage demo dataflash management routines changed to use the endpoint stream functions * - Added AVRStudio project files for each demo in addition to the existing Programmer's Notepad master project file * - Re-added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes * are reflected in the hardware (change was previously lost) * * * \section Sec_ChangeLog152 Version 1.5.2 - Released 31st July, 2008 * * - Fixed SwapEndian_32() function in Common.h so that it now works correctly (wrong parameter types) * - Updated RNDIS demo - notification endpoint is no longer blocking so that it works with faulty Linux RNDIS * implementations (where the notification endpoint is ignored in favour of polling the control endpoint) * - Fixed incorrect Vendor Description string return size in RNDIS demo for the OID_GEN_VENDOR_DESCRIPTION OID token * - Added very basic TCP/IP stack and HTTP/TELNET servers to RNDIS demo * - Fixed DFU bootloader exit causing programming software to complain about failed writes * - Fixed DFU bootloader EEPROM programming mode wiping first flash page * - Fixed Clear/Set Feature device standard request processing code (fixing MassStorage demo in the process) * - Added support for the ATMEGA16U4 AVR microcontroller * - Library licence changed from LGPLv3 to MIT license * * * \section Sec_ChangeLog151 Version 1.5.1 - Released 31st July, 2008 * * - Changed host demos to enable the host function task on the firing of the USB_DeviceEnumerationComplete event * rather than the USB_DeviceAttached event * - HID Usage Stack now forcefully cleared after an IN/OUT/FEATURE item has been completely processed to remove * any referenced but not created usages * - Changed USB_INT_DisableAllInterrupts() and USB_INT_ClearAllInterrupts(), USB_Host_GetNextDescriptorOfType(), * USB_Host_GetNextDescriptorOfTypeBefore(), USB_Host_GetNextDescriptorOfTypeAfter() to normal functions (from inline) * - Fixed USBtoSerial demo not sending data, only receiving * - Fixed main makefile to make all by default, fixed MagStripe directory case to prevent case-sensitive path problems * - ConfigDescriptor functions made normal, instead of static inline * - Pipe/Endpoint *_Ignore_* functions changed to *_Discard_*, old names still present as aliases * - Fixed ENDPOINT_MAX_SIZE define to be correct on limited USB controller AVRs * - Changed endpoint and pipe size translation routines to use previous IF/ELSE IF cascade code, new algorithmic * approach was buggy and caused problems * - Bootloaders now compile with -fno-inline-small-functions option to reduce code size * - Audio demos now use correct endpoint sizes for full and limited controller USB AVRs, double banking in all cases * to be in line with the specification (isochronous endpoints MUST be double banked) * - Added Interface Association descriptor to StdDescriptors.h, based on the relevant USB2.0 ECN * - Fixed MIDI demo, corrected Audio Streaming descriptor to follow the MIDI-specific AS structure * - Fixed HID class demo descriptors so that the HID interface's protocol is 0x00 (required for non-boot protocol HID * devices) to prevent problems on hosts expecting the boot protocol functions to be supported * - Added read/write control stream functions to Endpoint.h * - Fixed AudioOut demo not setting port pins to inputs on USB disconnect properly * - Added RNDISEthernet demo application * * * \section Sec_ChangeLog150 Version 1.5.0 - Released 10 June, 2008 * * - Fixed MIDI demo, now correctly waits for the endpoint to be ready between multiple note messages * - Added CDC Host demo application * - Added KeyboardFullInt demo application * - Endpoint and Pipe creation routines now mask endpoint/pipe size with the size mask, to remove transaction * size bits not required for the routines (improves compatibility with devices) * - Fixed AudioInput demo - now correctly sends sampled audio to the host PC * - Fixed AudioOutput demo oncemore -- apparently Windows requires endpoint packets to be >=192 bytes * - Shrunk round-robbin scheduler code slightly via the use of struct pointers rather than array indexes * - Fixed off-by-one error when determining if the Usage Stack is full inside the HID Report parser * - Renamed Magstripe.h to MagstripeHW.h and moved driver out of the library and into the MagStripe demo folder * - Added preprocessor checks to enable C linkage on the library components when used with a C++ compiler * - Added Still Image Host demo application * - The USB device task now restores the previously selected endpoint, allowing control requests to be transparently * handled via interrupts while other endpoints are serviced through polling * - Fixed device signature being sent in reverse order in the CDC bootloader * - Host demos now have a seperate ConfigDescriptor.c/.h file for configuration descriptor processing * - HostWithParser demos now have a seperate HIDReport.c/.h file for HID report processing and dumping * - Removed non-mandatory commands from MassStorage demo to save space, fixed SENSE ResponseCode value * - CDC demos now send empty packets after sending a full one to prevent buffering issues on the host * - Updated demo descriptors to use VID/PID values donated by Atmel * - Added DoxyGen documentation to the source files * - Fixed Serial_IsCharRecieved() definition, was previously reversed * - Removed seperate USB_Descriptor_Language_t descriptor, USB_Descriptor_String_t is used instead * - Removed unused Device Qualifier descriptor structure * - Renamed the USB_CreateEndpoints event to the more appropriate USB_ConfigurationChanged * - Fixed MassStorageHost demo reading in the block data in reverse * - Removed outdated typedefs in StdRequestType.h, superceeded by the macro masks * - Corrected OTG.h is now included when the AVR supports both Host and Device modes, for creating OTG products * - USB_DeviceEnumerationComplete event is now also fired when in device mode and the host has finished its enumeration * - Interrupt driven demos now properly restore previously selected endpoint when ISR is complete * - USB_HOST_TIMEOUT_MS is now overridable in the user project makefile to a custom fixed timeout value * - Renamed USB_Host_SOFGeneration_* macros to more friendly USB_Host_SuspendBus(), USB_Host_ResumeBus() * and USB_Host_IsBusSuspended() * - Renamed *_*_Is* macros to *_Is* to make all flag checking macros consistant, Pipe_SetInterruptFreq() is now * Pipe_SetInterruptPeriod() to use the correct terminology * - UnicodeString member of USB_Descriptor_String_t struct changed to an ordinary int array type, so that the GCC * Unicode strings (prefixed with an L before the opening quotation mark) can be used instead of explicit arrays * of ASCII characters * - Fixed Endpoint/Pipes being configured incorrectly if the maximum endpoint/pipe size for the selected USB AVR * model was given as the bank size * - HID device demos now use a true raw array for the HID report descriptor rather than a struct wrapped array * - Added VERSION_BCD() macro, fixed reported HID and USB version numbers in demo descriptors * - Cleaned up GetDescriptor device chapter 9 handler function * - Added GET_REPORT class specific request to HID demos to make them complaint to the HID class * - Cleaned up setting of USB_IsInitialized and USB_IsConnected values to only when needed * - Removed Atomic.c and ISRMacro.h; the library was already only compatible with recent avr-lib-c for other reasons * - All demos and library functions now use USB standardized names for the USB data (bRequest, wLength, etc.) * - Added USE_NONSTANDARD_DESCRIPTOR_NAMES token to switch back to the non-standard descriptor element names * * * \section Sec_ChangeLog141 Version 1.4.1 - Released 5 May, 2008 * * - Enhanced KeyboardWithParser demo, now prints out pressed alphanumeric characters like the standard demo * - Fixed MassStorage demo, read/writes using non mode-10 commands now work correctly * - Corrected version number in Version.h * * * \section Sec_ChangeLog140 Version 1.4.0 - Released 5 May, 2008 * * - Added HID Report Parser API to the library * - Added Mouse and Keyboard host demo applications, using the new HID report parser engine * - Added MouseFullInt demo, which demonstrates a fully interrupt (including control requests) mouse device * - Fixed incorrect length value in the audio control descriptor of the AudioOutput and AudioInput demos * - Added MIDI device demo application to the library * - Fixed problem preventing USB devices from being resumed from a suspended state * - Added new CDC class bootloader to the library, based on the AVR109 bootloader protocol * - Added header to each demo application indicating the mode, class, subclass, standards used and supported speed * - Functions expecting endpoint/pipe numbers are no longer automatically masked against ENDPOINT_EPNUM_MASK or * PIPE_PIPENUM_MASK - this should be manually added to code which requires it * - Fixed DFU class bootloader - corrected frequency of flash page writes, greatly reducing programming time * - Renamed AVR_HOST_GetDeviceConfigDescriptor() to USB_Host_GetDeviceConfigDescriptor() and AVR_HOST_GetNextDescriptor() * to USB_Host_GetNextDescriptor() * - Added new USB_Host_GetNextDescriptorOfTypeBefore() and USB_Host_GetNextDescriptorOfTypeAfter() routines * - Moved configuration descriptor routines to MyUSB/Drivers/USB/Class/, new accompanying ConfigDescriptors.c file * - Added new configuration descriptor comparator API for more powerful descriptor parsing, updated host demos to use the * new comparator API * - Fixed MassStorageHost demo capacity printout, and changed data read/write mode from little-endian to the correct * big-endian for SCSI devices * - Fixed macro/function naming consistancy; USB_HOST is now USB_Host, USB_DEV is now USB_Device * - Added better error reporting to host demos * - Added 10 microsecond delay after addressing devices in host mode, to prevent control stalls * * * \section Sec_ChangeLog132 Version 1.3.2 - Released April 1st, 2008 * * - Added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes * are reflected in the hardware * - Fixed CDC and USBtoSerial demos - Stream commands do not work for control endpoints, and the * GetLineCoding request had an incorrect RequestType mask preventing it from being processed * - Improved reliability of the USBtoSerial demo, adding a busy wait while the buffer is full * - Device control endpoint size is now determined from the device's descriptors rather than being fixed * - Seperated out SPI code into new SPI driver in AT90USBXXX driver directory * - Bootloader now returns correct PID for the selected USB AVR model, not just the AT90USB128X PID * - Added support for the RZUSBSTICK board * - Bicolour driver removed in favour of generic LEDs driver * - Added support for the ATMEGA32U4 AVR * - Added MANUAL_PLL_CONTROL compile time option to prevent the USB library from manipulating the PLL * * * \section Sec_ChangeLog131 Version 1.3.1 - Released March 19th 2008 * * - Fixed USB to Serial demo - class value in the descriptors was incorrect * - Control endpoint size changed from 64 bytes to 8 bytes to save on USB FIFO RAM and to allow low * speed mode devices to enumerate properly * - USB to Serial demo data endpoints changed to dual-banked 16 byte to allow the demo to work * on USB AVRs with limited USB FIFO RAM * - Changed demo endpoint numbers to use endpoints 3 and 4 for double banking, to allow limited * USB device controller AVRs (AT90USB162, AT90USB82) to function correctly * - Updated Audio Out demo to use timer 1 for AVRs lacking a timer 3 for the PWM output * - Fixed incorrect USB_DEV_OPT_HIGHSPEED entry in the Mass Storage device demo makefile * - Optimized Mass Storage demo for a little extra transfer speed * - Added LED indicators to the Keyboard demo for Caps Lock, Num Lock and Scroll Lock * - Added Endpoint_Read_Stream, Endpoint_Write_Stream, Pipe_Read_Stream and Pipe_Write_Stream functions * (including Big and Little Endian variants) * - Made Dataflash functions inline for speed, removed now empty Dataflash.c driver file * - Added new SetSystemClockPrescaler() macro - thanks to Joerg Wunsch * - Fixed Endpoint_ClearStall() to function correctly on full USB controller AVRs (AT90USBXXX6/7) * - Endpoint_Setup_In_Clear() and Endpoint_Setup_Out_Clear() no longer set FIFOCON, in line with the * directives in the datasheet * - Fixed PLL prescaler defines for all AVR models and frequencies * - Fixed ENDPOINT_INT_IN and ENDPOINT_INT_OUT definitions * - Added interrupt driven keyboard and mouse device demos * - Combined USB_Device_ClearFeature and USB_Device_SetFeature requests into a single routine for code * size savings * - Added missing Pipe_GetCurrentPipe() macro to Pipe.h * * * \section Sec_ChangeLog130 Version 1.3.0 - Released March 7th 2008 * * - Unneccesary control endpoint config removed from device mode * - Fixed device standard request interpreter accidentally processing some class-specific requests * - Added USE_RAM_DESCRIPTORS and USE_EEPROM_DESCRIPTORS compile time options to instruct the library * to use descriptors stored in RAM or EEPROM rather than flash memory * - All demos now disable watchdog on startup, in case it has been enabled by fuses or the bootloader * - USB_DEV_OPT_LOWSPEED option now works correctly * - Added ability to set the USB options statically for a binary size reduction via the USE_STATIC_OPTIONS * compile time define * - USB_Init no longer takes a Mode parameter if compiled for a USB device with no host mode option, or * if forced to a particular mode via the USB_HOST_ONLY or USB_DEVICE_ONLY compile time options * - USB_Init no longer takes an Options parameter if options statically configured by USE_STATIC_OPTIONS * - Endpoint_Ignore_* and Pipe_Ignore_* made smaller by making the dummy variable non-volatile so that the * compiler can throw away the result more efficiently * - Added in an optional GroupID value to each scheduler entry, so that groups of tasks can once again be * controlled by the new Scheduler_SetGroupTaskMode() routine * - Added support for AT90USB162 and AT90USB82 AVR models * - Added support for the STK525 and STK526 boards * - Added support for custom board drivers to be supplied by selecting the board type as BOARD_USER, and * placing board drivers in {Application Directory}/Board/ * - PLL is now stopped and USB clock is frozen when detatched from host in device mode, to save power * - Joystick defines are now in synch with the schematics - orientation will be rotated for the USBKEY * - Fixed USB_DEV_IsUSBSuspended() - now checks the correct register * - Fixed data transfers to devices when in host mode * - Renamed USB_DEV_OPT_HIGHSPEED to USB_DEV_OPT_FULLSPEED and USB_HOST_IsDeviceHighSpeed() to * USB_HOST_IsDeviceFullSpeed() to be in line with the official USB speed names (to avoid confusion with * the real high speed mode, which is unavailable on the USB AVRs) * * * \section Sec_ChangeLog120 Version 1.2.0 - Released February 4th, 2008 * * - Added USB_DeviceEnumerationComplete event for host mode * - Added new Scheduler_Init routine to preprepare the scheduler, so that tasks can be started and * stopped before the scheduler has been started (via Scheduler_Start) * - Connection events in both Device and Host mode are now interrupt-driven, allowing the USB management * task to be stopped when the USB is not connected to a host or device * - All demos updated to stop the USB task when not in use via the appropriate USB events * - Mass Storage Host demo application updated to function correctly with all USB flash disks * - Mass Storage Host demo application now prints out the capacity and number of LUNs in the attached * device, and prints the first block as hexadecimal numbers rather than ASCII characters * - Endpoint and Pipe clearing routines now clear the Endpoint/Pipe interrupt and status flags * - Shifted error handling code in the host enum state machine to a single block, to reduce code complexity * - Added in DESCRIPTOR_TYPE, DESCRIPTOR_SIZE and DESCRIPTOR_CAST macros to make config descriptor processing * clearer in USB hosts and DESCRIPTOR_ADDRESS for convenience in USB devices * - Added in alloca macro to common.h, in case the user is using an old version of avr-lib-c missing the macro * * * \section Sec_ChangeLog130 Version 1.1.0 - Released January 25th 2008 * * - Fixed DCONNI interrupt being enabled accidentally after a USB reset * - Fixed DDISCI interrupt not being disabled when a device is not connected * - Added workaround for powerless pullup devices causing false disconnect interrupts * - Added USB_DeviceEnumerationFailed event for Host mode * - AVR_HOST_GetDeviceConfigDescriptor routine no longer modifies ConfigSizePtr if a valid buffer * pointer is passed * - Added ALLOCABLE_BYTES to DynAlloc, and added code to make the size of key storage variables * dependant on size of memory parameters passed in via the user project's makefile * - Fixed incorrect device reset routine being called in USBTask * - Devices which do not connect within the standard 300mS are now supported * - Removed incorrect ATTR_PURE from Scheduler_SetTaskMode(), which was preventing tasks from being * started/stopped, as well as USB_InitTaskPointer(), which was breaking dual device/host USB projects * - Changed scheduler to use the task name rather than IDs for setting the task mode, eliminating the * need to have a task ID list * - ID transistion interrupt now raises the appropriate device/host disconnect event if device attached * - Fixed double VBUS change (and VBUS -) event when detatching in device mode * - Added ability to disable ANSI terminal codes by the defining of DISABLE_TERMINAL_CODES in makefile * - Removed return from ConfigurePipe and ConfigureEndpoint functions - use Pipe_IsConfigured() and * Endpoint_IsConfigured() after calling the config functions to determine success */